Getting a Beautiful Woodworking Finish With Shellac

Hello, how are you today? Welcome to our blog: URBAKI Woodworking.

We hope that you are very well and looking forward to a new post about woodworking.

Today we are going to share with you:

How to Get a Perfect Finish with Shellac

A shellac finish has been used by woodworkers since the early 1800s. Shellac is non-toxic, can be used as a sealer before applying a stain, can be mixed with nearly any color, and is easy to repair in the event of damage from use.

That being said, there are some drawbacks to using shellac as a final wood finish; shellac does not hold up well to heat or water, and it dries quickly when being applied, which leads many woodworkers to believe that applying a ​proper shellac finish can be difficult.

How Shellac Is Made

Shellac is derived from a resin that is secreted from an insect native to certain forests in southeast Asia. This insect secretion is scraped from the bark of trees and when processed, takes the form of small, light-brown or orange flakes.

To make an applicable woodworking finish, these flakes are mixed with alcohol. Woodworkers commonly use a two-pound-cut finish, which is to say a ratio of two pounds of shellac flakes per gallon of alcohol. Pre-mixed shellac found in home centers may be three-pound, but this can be cut if desired.

Applying Shellac

There are two commonly accepted methods for applying shellac: brushing and padding. To brush on shellac, use a fine, natural or china-bristle brush. Use a two or three-pound cut of shellac and apply generously with long, smooth strokes.

Since shellac dries quickly, be careful to avoid drips or blotchy areas when applying because unlike other finishes, you will likely not have time to over-brush to eliminate the blemish.


To apply shellac with a pad, use a clean piece of medium-weight cotton muslin. Lay down a smooth, even application of shellac in a single long, even stroke.

Before beginning to apply the shellac, place your cut of shellac into a squeeze bottle. Squeeze a liberal amount of shellac into the sock to act as a reservoir. Then wrap the muslin around the sock and hold the edges of the muslin behind the sock.

Squeezing the pad lightly should allow a small amount of shellac to seep through the muslin. The exposed shellac on the muslin surface of the pad should be even with no dripping.

When applying the pad to your woodworking project, you may need a bit of a lubricant. Mineral oil works great, as it will not affect the final color or finish. If your padding movement seems a bit "sticky," keep a small bowl with a little bit of mineral oil handy for light dipping.

With a very small amount of mineral oil on the loaded pad, you're ready to begin applying the shellac to the wood. To start, do not place the pad directly onto the wood and begin rubbing; instead, ease the pad on and off the stock to avoid any blotchy spots.

The best way to describe the motion is to work much like an airplane taking off and landing.

Once the pad is on the wood, work in somewhat irregular patterns rather than just with the grain. This will ensure a thorough coverage. As you need more shellac, simply squeeze the pad a bit.

Many woodworkers like to use a combination of brushing and padding. They will apply the shellac with a brush and then immediately smooth it out with a piece of muslin. Use long strokes moving with the grain of the stock.

Completing the Shellac Finish

After the first coat of shellac dries, lightly sand with 400-grit sandpaper. Wipe off the white residue and apply a second coat. Repeat until the desired number of coats have been applied.

This direct application will result in a high-gloss finish. If a less glossy, satin finish is preferred, try buffing out the final coat with some 0000 steel wool and (non-silicon based) paste wax. Lightly work the wax over the finish until it is thoroughly covered. Allow the wax to dry and then wipe off and buff to a lustrous finish.


Brushes can be easily cleaned after applying shellac with alcohol, as this will effectively cut the shellac until the brush is clean. The alkaline ammonia dissolves the shellac quickly and easily.

After the shellac is completely gone, wash the brush with soap and warm water to keep the bristles soft. Dry the bristles and store the brush in the container in which it came.

Repairing Shellac Finishes

Shellac finishes should be kept away from water, as they will become dull or even have a white residue appear when exposed to moisture. Should your shellac finish develop water spots, repair is relatively simple.

Use straight alcohol on a pad and remove the shellac from the offending area. Then pad or brush on a series of coats of shellac and rub it out until the finish is even.

Should a surface scratch appear through the finish, use a fine artist's brush to fill the scratch with shellac. Rub out the finish to even out the color between the repaired scratch and the surrounding finish.


We hope you enjoy watching this video about how to get a perfect  woodworking finish with Shellac

Source: Fabian's Tiny Workshop

Did you find this post Useful or Inspiring? Save THIS PIN to your Woodworking Board on Pinterest!

Ok, That is all for now…

We hope that you enjoyed the content.

See you in the next post!

You may also like 👇🏼👇🏼

Go up

This site uses cookies: Read More!

Follow Us on Pinterest!! 😍